ASTM B221-08 PDF

Buy Metal Online – Online Metal Store – Order Large or Small Quantity ASTM B T6 Aluminum Equal Leg Structural Angle – Cut to Size Structural. Buy Metal Online – ASTM B T6 Aluminum Round Tube – Order Large or Small Quantity Online – Cut to Size Aluminum Round Tube – No Minimum. Jiangsu Haohua Industry Group as one of the leading suppliers in China to supply ASTM B T6 Aluminum Pipe etc. [Contact person:Ms chris ; Email.

Author: Goltit Muzahn
Country: Syria
Language: English (Spanish)
Genre: Love
Published (Last): 21 June 2008
Pages: 105
PDF File Size: 1.70 Mb
ePub File Size: 11.55 Mb
ISBN: 409-4-57191-805-9
Downloads: 28114
Price: Free* [*Free Regsitration Required]
Uploader: Yorg

L Only in tube form. Current edition approved Oct. For a tube having a diameter larger than can be properly mounted for polishing and examination, the portions of the cross section polished for examination may consist of an arc about 1?

B — 05a Standard Speci? Unalloyed aluminum contains a minimum of J Minimum yield strength for tube, The electrical conductivity shall be determined in accordance with Practice E in the following locations: M Properties not applicable to extruded tube over 2. Each sample shall be taken from material considered acceptable in accordance with the lot-acceptance criteria of Table 4.

To determine conformance to this speci? Weight, max per Piece, lb Max Width: B The thickness of any element of a pro? Tube Other Than Round Angularity: Originally approved in Elongation of cut-out round specimens is measured in 43 specimen diameter. Rod, Bar and Pro? Any requirement not so covered is subject to negotiation between the producer and purchaser.


A superscript epsilon e indicates an editorial change since the last revision or reapproval. O H H up through 5. A minimum of three adjacent replicate specimens shall be taken from each sample and tested. C For the purpose of determining conformance to these limits, an observed value or a calculated value obtained from analysis shall be rounded to the nearest unit in the last right-hand place of the?

Heat Treatment and Reheat-Treatment Capability Specimens shall be selected at random and shall be, if possible, a minimum of 2 by 4 in. If the chemical composition has been determined during the course of manufacture, analysis of the? The heat-treated sample may be tested prior to 4 days natural aging but if they fail to conform to the T42 temper properties, the test may be repeated after completion of 4 days natural aging without prejudice.

K Bismuth and lead shall be 0.

ASTM B221-08 6061-T6 Aluminum Bar Steel Round Bars / Tubes For Stakes , Tines

Conformance shall be determined by analyzing samples taken when the ingots are poured, or samples taken from the? NOTE 2—For rolled or cold-? The test location shall be 9 Using a magni?

Test specimens may be prepared by machining a?

ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard. Should any analysis by the producer or the purchaser establish that an Others element exceeds the limit of Each or that the aggregate of several Others elements exceeds the limit of Total, the asttm shall be considered nonconforming.


Analysis shall be made for the elements for which limits are shown in this table. D Others includes listed elements for which no speci?

ASTM B T6 Aluminum Pipe-Aluminium Products-Jiangsu Haohua Industry Group

As much n221-08 the rejected material as possible shall be returned to the producer or supplier by the purchaser. A designation not in con? Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters.

This standard is subject to revision at any time by the responsible technical committee and must be reviewed every? Last previous edition approved in as B — M Composition of cladding alloy applied during the course of manufacture. The correctness of cladding alloy used can usually be veri?

G Material in the T42 and T62 tempers is not available from the material producers. A number in parentheses indicates the year of last reapproval.